Activity Stream
-
Older Activity
-
Today, 10:17Bud, people need to know what is happening with the spent case or loaded round. Is it ejecting and closing on an empty chamber, is it like one of...14 replies | 305 view(s)
-
Today, 10:07Thanks, I contacted them yeasterday. Stock just arrived. A bit steep though. 11inch Saint Victor R36K , 16 inch R42K138 replies | 50574 view(s)
-
Today, 08:33I'm still confused about what the actual nature of your failure is: 1. Failure to cycle, i.e. bolt not moving back far enough and not picking up a...14 replies | 305 view(s)
-
Today, 07:41I would also check the gas port on the barrel. Some holes are not drilled to the correct size and it differs between manufacturers. It might well be...14 replies | 305 view(s)
-
Yesterday, 12:34Locks back manually just fine. Gas block is aligned correctly. What can I check on the gas tube? There is air flow through the tube on its own. ...14 replies | 305 view(s)
-
18-04-2024, 22:27oafpatroll replied to a thread What happens IF the ANC does not get re-elected in General DiscussionI'm pretty sure we're doomed to bottom out before we start coming out of the hole. Our electorate values everything but the stuff proven to make...144 replies | 42135 view(s)
-
18-04-2024, 20:09More recent info particularly from the Social Research Foundation (Frans Cronje) tends to confirm my belief that we are likely to get another five...144 replies | 42135 view(s)
-
18-04-2024, 16:56Describe the jam, or even better, provide pictures. There are many things from the end of the buffer tube to the gas block, that can cause an AR15 to...14 replies | 305 view(s)
-
18-04-2024, 16:29Does it lock back if you manually pull the charging handle back. Is there possibly too much play in the bolt catch. Sometimes magwell or catch cut...14 replies | 305 view(s)
-
18-04-2024, 14:54Builders Warehouse?5 replies | 21001 view(s)
-
18-04-2024, 14:51I was gifted one of these this morning. Busy looking around to find where I can get the 6mm blanks,.5 replies | 21001 view(s)
-
18-04-2024, 13:19Thanks yes I full size all my brass. Except for the gas key possibility, what other suggestions do you guys have. Could it possibly be something...14 replies | 305 view(s)
-
18-04-2024, 13:18Singers are also the rarest, and lowest production volume of the WW2 1911 makers. Also as Paul points out and something almost everyone has...5 replies | 205 view(s)
-
18-04-2024, 10:14During WW2 many companies were making many guns for the war effort. 1911s were made by Remington Rand... not Remington. Remington Rand is/was a...5 replies | 205 view(s)
-
18-04-2024, 09:21noted14 replies | 305 view(s)
-
18-04-2024, 09:12Thanks for the tip. I'm in the western cape though.14 replies | 305 view(s)
-
18-04-2024, 09:00When i had issues a few years ago with cycling it was my bolt carrier group gas key that was loose and not torqued according to spec and not properly...14 replies | 305 view(s)
-
18-04-2024, 08:40The same thing happens with factory ammo.14 replies | 305 view(s)
-
18-04-2024, 08:36begin with factory ammo to rule out the possibility of reloading error .14 replies | 305 view(s)
-
18-04-2024, 08:30Hi all gun people, hope everyone is doing well. I've got an issue with a Smith & Wesson M&P Sport II 223 rifle, maybe someone can assist. Please...14 replies | 305 view(s)
-
18-04-2024, 01:57Here : If I remember right the A1 model was a upgraded from the original WW1 1911 in 1928. They made several changes, trigger, safety etc. ...5 replies | 205 view(s)