Results 1 to 10 of 27
Thread: .357 magnum PIN load
-
11-04-2015, 22:39 #1
- Join Date
- Sep 2008
- Posts
- 1,898
.357 magnum PIN load
I am looking for a PINload for 357 Magnum using frontier 158 grn RN. Ideally using MS 200.
Any help would be much appreciated.
-
11-04-2015, 23:23 #2
- Join Date
- Aug 2012
- Location
- Stella
- Age
- 46
- Posts
- 10,870
Re: .357 magnum PIN load
Goblin, what is your reason for using MS200? I wouldn't use MS 200 in my .357 if you paid me and promised me a new rollie. The pressure spike is generally considered to be too fast and too high. Also, MP 200 gives a better case fill which should result in better accuracy. Some people use S221((?) or S265 for long barreled rollies.
And somewhere I read that heavier bullets (200gr+) give better results.
If pin shooters often use MS200, please ignore my post.
-
12-04-2015, 00:17 #3
- Join Date
- Feb 2013
- Location
- JHB South Africa
- Age
- 53
- Posts
- 4,033
Re: .357 magnum PIN load
A 180 grain lead bullet (not too hard) at just on 220 Fac does the trick.
I still have some old load data from my pin days, used S265 and .38 Spl cases exclusively
Will see if I can find it in the morrow
-
12-04-2015, 09:10 #4
- Join Date
- Dec 2011
- Age
- 71
- Posts
- 999
Re: .357 magnum PIN load
I'm not a revolver specialist, so take this with caution and use at your own risk.
Most pin shooters use 180 to 200 gr bullets. I started with 158 gr, but battled to get the pins off the table and found the recoil heavy. I would be hesitant to use MS200.
My 158gr CMJ load was 7,7gr MP200 for a velocity of 1140 ft/sec, factor 180 (Ruger SS, 4" barrel)
My current load is 180gr CMJ with 7,0gr MP200 for vel. of 1000 ft/sec, factor 180.
Some pin shooters use .38 Special cases with extra long / extra heavy bullets, but I don't have the specs.
-
13-04-2015, 13:05 #5
- Join Date
- Oct 2012
- Location
- Noord van die biltong gordyn.
- Age
- 57
- Posts
- 9,093
Re: .357 magnum PIN load
Yes, the common 357 Mag pin loads are 180 gn to 200 gn. There are those who insist on using the 230 gn wad-cutter ("pin grabber") bullets, made by Josyd.
A 158 gn bullet could move the pins off the table, but will have to be pushed at max pressure to do so. It will also very likely tend to exit the pins, transferring lots of inertia on the backstop, in stead of inside the pin. A lead SWC of 158 gn works better, as it tends to deform more than a CMJ, and "grab" onto the wood fibers inside the pin.
MS200 is definitely unsuitable. Do not use anything faster than MP200. For heavy bullets, S265 is popular, but I find it leaves too much unburned powder if not pushed to max pressure (which is not needed).
For the longer (heavier) cast bullets, that do not have a crimp groove far enough forward, to fit in the cylinder when crimped in a 357 case, you could use a 38 Spl case. Just ensure the case head is the same thickness as a 357. Some older cases had weak heads. With long (heavy) bullets, you want to maximize the case capacity by seating the bullets out as far as possible. Cylinder lengths vary between different revolvers, so tailor your loads to your revolver's measurements.
-
13-04-2015, 15:09 #6
- Join Date
- Feb 2013
- Location
- JHB South Africa
- Age
- 53
- Posts
- 4,033
Re: .357 magnum PIN load
Okay. I found my data
Please use at own risk, as I will accept zero responsibility, so I suggest working up to them carefully
Revolver was a Taurus 608 8 inch non compensated barrel
Primers were always Federal Small pistol
Powder S265
180 Grain lead bullet .357
In .357 mag case 15.50 grains for 1246 Fps
In .38 Spl Case Max 13.7 Grains for 1366 Fps
-
13-04-2015, 21:04 #7
- Join Date
- Jul 2008
- Posts
- 1,826
Re: .357 magnum PIN load
As stated before by others, USE AT OWN RISK.
Taurus 608 6"
Primers Federeral SPP
38 spl cases
S265 9,7gr
Cast Josyd 195gr
Never seen a pin stay around when hit centre mass
-
16-04-2015, 18:59 #8
- Join Date
- Sep 2008
- Posts
- 1,898
Re: .357 magnum PIN load
Thanksfor all the advise guys appreciate it. Katlagter is your MP load for the 180 grainers in. 357 mag cases or. 38 spl cases? I have a chrono going at a very cheap price by the way!
-
16-04-2015, 19:02 #9
- Join Date
- Sep 2008
- Posts
- 1,898
Re: .357 magnum PIN load
Offer on the chrono is exclusive to Katlagter as it is his. Are you going to be at Huntex on Friday - as I don't really want to, but am willing to return it to you. Am shooting my first pin match in ages with the club inTzaneen this weekend. Looking very much forward to this!
-
16-04-2015, 19:21 #10
- Join Date
- Sep 2009
- Posts
- 4,390
Re: .357 magnum PIN load
Thanks Yeti and Theunsb - your data store for sometime in the future.
ATB with the pin match, GG!
Similar Threads
-
.357 Magnum 125gr/158gr MP200 load data?
By Brendank in forum Reloading DiscussionsReplies: 4Last Post: 04-07-2015, 16:45 -
[FOR SALE] 44 Magnum Winchester Lever Action/Lama 44 magnum 6 inch + Feeler on Vektor H5
By Phumba in forum Firearms / Guns for SaleReplies: 28Last Post: 03-11-2013, 19:28 -
.357 Magnum S265 Load Leaves flakes in Barrel
By Reloader270 in forum Reloading DiscussionsReplies: 4Last Post: 01-04-2011, 21:11 -
Need load data for .357 magnum - 160gr. bullet + S121
By Blade_BKA in forum Reloading DiscussionsReplies: 9Last Post: 19-10-2010, 13:45
Bookmarks